hi-pitched click sounds

• FN 12 0

  消息来自 full name，发表于 …
  bottrop 写于 … - 显示被引用的消息

  @Ziya
  i cant hear or see a click in that sample at 1170
  
  regards bottrop
  are they click-ed or not? im confused how would this be a gray area...
  
  i did not hear any artifacts going over the samples, he still isn't saying if the imperfection is audible in an editor
• 消息来自 full name，发表于 …
  ziyametedemircan 写于 … - 显示被引用的消息

  One of these samples "D 400" has a defect in the left channel ("D 400L"). Between 1070 and 1073.
  
  
  I've seen such problematic samples in a collection on web archive org
  At least there is no problem on the right channel.
  If you want to use it, you can set the "sample start offset" parameter to 1100 (or use only the left channel).
  i've put 1100 into the global settings for that parameter, glitch is there still
  
  can you tell me how to use only one channel? btw did you mean " use right channel only " ?
• 423 17

  消息来自 bottrop，发表于 …
  here is the sample in a sf2
  D400.sf2
• ZI 203 0

  消息来自 ziyametedemircan，发表于 …

  bottrop@Ziya
  i cant hear or see a click in that sample at 1170

  1070 ~ 1073 (in polyphone) Type 1069 into loop-start. Then zoom in (too much) to the part with the green bar.
• 消息来自 ziyametedemircan，发表于 …
  _{Due to a short Internet outage, the message was sent twice..}
• 消息来自 ziyametedemircan，发表于 …

  full name
  
  i've put 1100 into the global settings for that parameter, glitch is there still
  
  can you tell me how to use only one channel? btw did you mean " use right channel only " ?

  The glitch is still there, of course. Otherwise why write 1100 in sample-start-offset? We use that parameter to get the starting point just after that glitch.
  
  In order to use only one channel: you have to unlink the relevant samples from the tools menu and delete the defective one from the instruments section and set its pan value to 0.
• FN 12 0

  消息来自 full name，发表于 …
  ziyametedemircan 写于 … - 显示被引用的消息

  full name
  
  i've put 1100 into the global settings for that parameter, glitch is there still
  
  can you tell me how to use only one channel? btw did you mean " use right channel only " ?

  The glitch is still there, of course. Otherwise why write 1100 in sample-start-offset? We use that parameter to get the starting point just after that glitch.
  
  In order to use only one channel: you have to unlink the relevant samples from the tools menu and delete the defective one from the instruments section and set its pan value to 0.
  The glitch is still there, of course. Otherwise why write 1100 in sample-start-offset? We use that parameter to get the starting point just after that glitch.
  
  In order to use only one channel: you have to unlink the relevant samples from the tools menu and delete the defective one from the instruments section and set its pan value to 0.
  u recommended i try sample offset, i tried it, saved the change, even though now samples are triggered after the supposed glitch, glitch is still there. idk if you understand
  
  i succeeded with that panning tip tho, the soundfont is clean now! i didn't know you can remove individual channels that's why i wasn't getting what you mean
• 423 17

  消息来自 bottrop，发表于 …
  so i was 100 samples too far, but at 1070 i see no clicks either (D400.png). downloaded the sample anew (named it D400a.png), unzipped with 7zip; no clicks for me, as far as i can hear and see.
  have you tried the D400.sf2?
  watch the attached .png's
  D400a.png

  D400.png
• ZI 203 0

  消息来自 ziyametedemircan，发表于 …
  bottrop 写于 … - 显示被引用的消息

  so i was 100 samples too far, but at 1070 i see no clicks either (D400.png). downloaded the sample anew (named it D400a.png), unzipped with 7zip; no clicks for me, as far as i can hear and see.
  have you tried the D400.sf2?
  watch the attached .png's
  The difference between the two: I viewed this sample with Polyphone software, you viewed it with another wave editor.
  Now I looked again with Audacity and you are right, there is no clipping but there is a high dB value (at 0dB).
  When I normalize it to -1dB and import it into Polyphone, there is no clip.
  In this case, can we say that when the sample goes above a certain dB value, the dll used by Polyphone to load it clips it?
• 423 17

  消息来自 bottrop，发表于 …
  you are right, Ziya, i just exported the D400 sample from Polyphone (1.9) and there is a click at L 1070.
  so the solution is to normalize the samples before importing them in Polyphone.
  regards bottrop

登录或注册后即可参与讨论。